雙組份打膠機呈現花膠的問題無論是進口的立式打膠機仍是臥式打膠機都會(huì )經常呈現的一種毛病，雙組份打膠機一般呈現花膠這種毛病大多是由以下幾個原因導致的。
The two-component gluing machine presents the problem of flower glue, which is often found in both imported vertical and horizontal gluing machines. The problems of two-component gluing machines are mostly caused by the following reasons.
1、雙組份打膠機的混膠器內膠體過多固話，阻力增大。
1. There are too many colloids in the mixer of the two-component dispenser, and the resistance increases.
2、A或B膠膠桶內無膠，膠已用完。
2. There is no glue in a or B glue barrel, and the glue has been used up.
3、A或B膠膠桶內有空氣。
3. There is air in rubber barrel a or B.
4、針閥或單向閥阻塞。咱們仔細觀察小編所寫的導致花膠的毛病原因會(huì )發現大多是因為設備沒有定時保護清洗導致的。所以咱們一定要牢記設備一定要定時保護清洗的良好習慣。
4. The needle valve or check valve is blocked. If we carefully observe the reasons for the problems of the glue, we will find that most of them are caused by the equipment is not regularly protected and cleaned. So we must keep in mind that the equipment must be regularly protected and cleaned.

一種狀況是因為咱們將打膠機的打膠速度設置的過快導致的。有的客戶為了加速自己的生產節奏追逐生產計劃，將打膠速度以為調整的過快，導致膠體還沒有徹底達到合格標準機頭就已經移動到下一個位置進行打膠操作了.
One is because we set the glue speed of the glue machine too fast. In order to speed up their own production rhythm and pursue the production plan, some customers think that the gluing speed is adjusted too fast, resulting in the glue has not completely reached the qualified standard, the machine head has moved to the next position for glue operation
假如咱們需要加速打膠的速度調整了打膠機的移動參數的話，那么咱們對應的也應該對供膠體系也進行相應的設置，比方這時候咱們就需要加大供膠壓力，增大打膠機的出膠速度來配合目標的移動速度的增加。
If we need to speed up the gluing speed and adjust the moving parameters of the gluing machine, then we should also set the corresponding glue supply system. For example, at this time, we need to increase the glue supply pressure and the glue output speed of the gluing machine to match the increase of the moving speed of the target.
假如咱們僅僅是獨自的增加了打膠機的移動速度而沒有對壓力進行調理的話就很有可能呈現打膠不豐滿的狀況發生。另外一種狀況跟打膠機的速度差不多便是咱們的供膠壓力不足導致的。
If we only increase the moving speed of the gluing machine alone and do not regulate the pressure, it is likely that the glue is not full. Another situation is that the speed of the glue machine is almost the same, which is caused by the insufficient glue supply pressure.
雙組份打膠機產生打膠不豐滿的原因可以參考種狀況。除了以上小編說的人為原因導致的這個毛病以外設備的零部件損壞也會(huì )導致這個問題，比方機頭感應器損壞。
The reason of the two-component gluing machine is not full can refer to the situation. In addition to the above small series of human causes of this problem, equipment parts damage will also lead to this problem, such as head sensor damage.