一、打膠機的特點來介紹雙組份打膠機

　　First, the characteristics of the glue machine to introduce the double component glue machine

　　1、用高壓空氣在設定的時間內，使用腳踏開關或自動把液體推出。

　　1. Use the high pressure air in the set time, use the foot switch or automatically release the liquid.

　　2、點膠機控制器有點滴,連動,定時滴膠功能;點滴就是直接觸發腳踏開關滴膠,并且可通過時間控制點膠量精確度;連動就是用腳踏板之關閉時間多久來控制滴膠時間;定時滴膠就是觸發開關通過時間控制滴膠

　　2, dispensing controller with drip, linkage, timing function is directly trigger glue; drop foot switch glue, and through the dispensing time control accuracy; is used to control the closing time how long time the glue pedal linkage; timing trigger switch control is epoxy glue through time

　　3、自動雙組份打膠機采用高精度數碼定時控制器,精準控制每次滴定時間,精確到毫秒，正確地控制液料流量，絕不會(huì )浪費液料。

　　3, the automatic dual component glue machine adopts high precision digital timing controller, precisely control every titration time, accurate to milliseconds, control liquid flow rate correctly, and will never waste liquid material.

　　4、只要調節好氣壓，出膠時間和選擇適當的針咀，便輕易改變每次注滴量和注滴時間。

　　4, as long as the pressure is adjusted, the time of glue is out and the proper needle Tsui is chosen, the amount of drip and the time of drip are easily changed.

　　5、調整自動點膠閥尾部調節螺絲和膠水的壓力可控制出膠量大小。膠量調節螺絲順時鐘向下轉動為減小膠量，逆時鐘方向轉動為 加大膠量。

　　5, adjusting the pressure of the rear adjusting screw and glue of the automatic dispensing valve can control the size of the glue. The glue quantity adjusting screw rotates down the clock to reduce the amount of glue, and turns against the clock direction to increase the amount of glue.

　　二、雙組份打膠機的基本工作流程如下：

　　Two. The basic working process of the double component glue machine is as follows:

　　(1)在打膠機的控制面板設定個好打膠機的打膠速度(默認也可以)

　　(1) first in the control panel of the glue machine set the glue speed of a good glue machine (by default)

　　(2)將玻璃放入打膠機的工作區域

　　(2) put the glass into the working area of the gluing machine

　　(3)當設備檢測到玻璃后吸盤會(huì )自動吸住玻璃以免玻璃在打膠過程中晃動或人為晃動正在進行打膠的玻璃

　　(3) when the device detects the glass sucker automatically so as not to suck the glass glass glue in the process of shaking in the shaking is glue or man-made glass

　　(4)當洗盤對玻璃固定好后，打膠機的機頭就開始對玻璃進行打膠動作(不需要進行對玻璃的厚度以及寬度進行設置，打膠機會(huì )自動調整并工作)

　　(4) when fixed on the glass pad, head of glue machine began to glass glue (without the need for action on the glass thickness and width setting, glue the opportunity to automatically adjust and work)

　　(5)以上的步驟重復3次將玻璃的4邊全部完成打膠后整個玻璃的打膠工作就算完成了。

　　(5) the above steps are repeated 3 times when all the 4 sides of the glass are finished and the whole glass is finished.

　　一般在默認的打膠速度每分鐘少可以完成一款2米5見方的玻璃打膠工作，如果將打膠機的打膠速度加快生產會(huì )進一步提高。

　　Generally speaking, at the default glue speed, we can finish at least 2 meters, 5 square glass glue work per minute, if we speed up the glue speed of the glue machine, we will further improve the production efficiency.

　　本文由雙組份打膠機為您提供，我們的網站是:http://whooo.net我們將以全心全意的熱情為您提供更的服務，歡迎您的訪問!

　　This article is provided by two component glue machine. Our website is: http://whooo.net, we will provide you with better service with wholehearted enthusiasm, welcome your visit.