涂布機膠水出膠斷斷續續應該怎樣辦

　　What should I do if the glue on the coating machine comes out intermittently

　　假如是打膠的時分呈現斷斷續續，這種狀況肯定是要不得的，由于這個肯定會(huì )影響到正常的消費作業。涂布機膠水出膠斷斷續續緣由當然是很多的，我們要找準緣由，然后想出對策才行，而這個招致這種現象的緣由又比擬的復雜，假如不是經歷比擬豐厚的工作人員的話，是很難剖析出一切的緣由，然后去處理問題的。今天就來為大家引見一下這種斷斷續續的狀況終究是什么緣由招致的。

　　If the glue is applied intermittently, this situation is definitely unacceptable as it will definitely affect normal consumption operations. There are many reasons for the intermittent dispensing of glue on the coating machine, and we need to identify the reasons and come up with countermeasures. However, the reasons for this phenomenon are quite complex. Without experienced staff, it is difficult to analyze all the reasons and deal with the problem. Today, let me introduce to you the reasons behind this intermittent situation.

　　涂布機膠水出膠斷斷續續能夠先思索一下是不是環境溫度呈現了一些異常狀況，這里所謂的斷斷續續我們也能夠將其了解為是拉絲的這種現象，那這個有可能是出在膠水上面。我們在打膠的時分用到的膠水普通都是要在0℃到5℃之間停止保管，也就是放在冰柜里面停止保管，但假如是庫房里面的工作人員在保管的時分沒有保管得當，那就有可能會(huì )招致這個膠水的性狀質量發作了改動，那在打膠的時分就是呈現拉絲或者呈現斷斷續續。

　　The intermittent dispensing of glue from the coating machine can be considered as an abnormal condition in the environmental temperature. Here, we can also understand that the intermittent dispensing is a phenomenon of wire drawing, which may be caused by the glue. The glue we use when gluing usually needs to be stored between 0 ℃ and 5 ℃, that is, stored in the freezer. However, if the warehouse staff do not properly store it during storage, it may cause changes in the quality of the glue's properties, resulting in a brushed or intermittent appearance during gluing.

　　在線式視覺涂布機.jpg

　　Online visual coating machine.jpg

　　這也間接的闡明這批膠水可能就是不合格的，那遇到這種狀況就需求中止運用這批膠水，要換合格的膠水運用。接下來還有一種狀況就是打膠的時分高度呈現了一些問題，假如是這個高度很高的話，那么間隔太遠了就呈現斷斷續續的問題。就能夠思索把這個高度恰當的調低一點。

　　This indirectly indicates that this batch of glue may be unqualified, and in such a situation, it is necessary to suspend the use of this batch of glue and replace it with qualified glue. The next situation is that there are some issues with the height when applying glue. If the height is too high, then the interval is too far, resulting in intermittent problems. We can consider lowering this height appropriately.

　　涂布機膠水出膠斷斷續續還有一種狀況就是膠水需求停止攪拌，但假如這個攪拌的不合理，比方說在攪拌的時分攪拌的不平均，那么打膠的時分斷斷續續，這種狀況就有可能會(huì )發作。所以要提示工作人員在上班之前就需求做好這些準備，比方說工作人員到庫房里面去把膠水拿出來了之后，要提早把膠水放到設備里面，要提早將其攪拌好，攪拌平均了之后打膠就不容易呈現這個斷斷續續的問題了。接下來還有一種可能的狀況就是壓力設置呈現了一些問題。比方這個涂布機里面的壓力設置太小了，或者是四周的環境溫度太低了，而里面的壓力又沒有重新設置，那么一旦壓力不夠打膠的時分就不容易打出來就容易斷斷續續。

　　The glue dispensing of the coating machine is intermittent, and there is also a situation where the glue needs to be stopped from mixing. However, if the mixing is not reasonable, such as uneven mixing during mixing, then the glue dispensing may be intermittent, and this situation may occur. So it is necessary to remind the staff to make these preparations before going to work. For example, after the staff go to the warehouse to take out the glue, they should put the glue into the equipment in advance and mix it well. After mixing evenly, the intermittent problem of glue application is less likely to occur. Another possible scenario is that there are some issues with the pressure setting. For example, if the pressure setting inside the coating machine is too low, or the ambient temperature around is too low, and the pressure inside has not been reset, then once the pressure is not enough to apply glue, it is not easy to apply it intermittently.

　　本文由  立式丁基膠涂布機  友情奉獻.更多有關的知識請點擊  http://www.whooo.net/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會(huì )陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a vertical butyl rubber coating machine For more related knowledge, please click http://www.whooo.net/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.