1.將裝好膠水的針筒放入針筒夾持器后并固定。比如裝AB膠，將A膠和B膠分別從壓力桶接到膠槍A、B進膠口，A、B膠分別通過三通到混合管時開始混合，膠水混合程度由混合管長度決定，只需控制壓桿即可控制膠水通斷，由一連串左右旋葉片相互垂直排列在套管內組成，A、B膠水經過混合管時進行連續的切割與重合為均勻的混合液，以保證出膠量精確。
1. Put the syringe loaded with glue into the syringe holder and fix it. For example, install AB glue, connect glue a and B from the pressure barrel to the glue inlet of glue gun a and B respectively, and the glue a and B begin to mix when they pass through the three-way to the mixing pipe respectively. The mixing degree of glue is determined by the length of the mixing pipe. Just control the pressure rod to control the on-off of glue, which is composed of a series of left and right rotating blades vertically arranged in the casing, a B. when the glue passes through the mixing pipe, it shall be continuously cut and overlapped into a uniform mixing liquid to ensure the accurate glue output.
2.連接氣閥，將點膠機的點膠控制器口通過氣管連接到針筒，并把針筒氣閥連接到點膠控制器的AIRIN，并且連接點膠機和點膠控制器的電纜線。
2. Connect the air valve, connect the dispensing controller port of the dispensing machine to the syringe through the air pipe, connect the syringe air valve to the airin of the dispensing controller, and connect the cable between the dispensing machine and the dispensing controller.

3.將點膠機的點膠接口通過電纜線連接到點膠控制器的信號輸入接口，把腳踏板連接到點膠機的運行接口上，以控制點膠機的運行。將Z軸的連接電纜插頭與點膠機Z軸連接。如所用點膠控制器同點膠機的連接器型號相同，可以根據連接器的芯數不同來看出點膠機的點膠和運行等連接口，二芯點膠，三芯運行。
3. Connect the dispensing interface of the dispensing machine to the signal input interface of the dispensing controller through cable, and connect the foot pedal to the operation interface of the dispensing machine to control the operation of the dispensing machine. Connect the connecting cable plug of the z-axis with the z-axis of the dispensing machine. If the dispensing controller used is the same as the connector model of the dispensing machine, you can see the connection ports of dispensing and operation of the dispensing machine, two core dispensing and three core operation according to the number of cores of the connector.
4.將手持式編程器通過串口線選擇到點膠機左側的接口上，如果所用點膠控制器同點膠機背面的連接器型號不相同，可以根據點膠控制器的說明書進行電纜線的配制和連接。
4. Select the hand-held programmer to the interface on the left side of the dispensing machine through the serial port cable. If the dispensing controller used is different from the connector model on the back of the dispensing machine, the cable can be prepared and connected according to the instructions of the dispensing controller.
本文由雙組份打膠機友情奉獻.更多有關的知識請點擊:http://whooo.net我們將會(huì )對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.
This article is dedicated by the two-component glue applicator. For more information, please click: http://whooo.net We will answer your questions in detail. You are welcome to log in to the website and leave a message