每次調整打膠情況需要進行數據保存
時間:2018-03-01 來源:http://whooo.net/ 發布人:昌盛機械
1、下班時需要清理膠頭,關閉連線,把旋轉開關旋轉到清洗和手動狀態,按下排膠啟動鍵,再按排膠閥鍵,這時膠頭出膠,打開黑膠減壓閥發排壓,降下壓力后關閉擰緊,待膠頭出膠全是白膠后按下排膠閥鍵,間隔5秒左右再次按下排膠閥鍵降白膠壓力,待壓力降到1以下關閉排膠閥。
Need to clean the rubber head 1, work, first close the connection, the rotary switch is rotated to the manual cleaning and discharging state, press the start button, then press button when discharging valve, rubber head glue, open the black glue valve pressure drop under pressure after publishing, close to tighten, head is full of glue glue according to the lower glue glue valve key, the interval of about 5 seconds again press the row key drop glue glue valve pressure, the pressure to be below 1 closed discharging valve.
2、生產時需要把玻璃里面一張標簽撕掉或貼到玻璃的下方,防止光電感應開關感應到誤動作損壞膠頭。在自動狀態時注意不要用手或其他異物遮擋光電開關,有問題時及時按下急停開關或關閉電源。
2, in production, we need to tear off a label in the glass or stick it down to the bottom of the glass, so as to prevent the photoelectric induction switch from causing the misaction to damage the glue head. In automatic state, do not use hand or other foreign objects to shield the photoelectric switch, when the problem is in time to press the stop switch or turn off the power.
3、打膠時若膠頭殘余膠較多時需及時清理,清理時注意防止輔助傳送傷手,玻璃平整度不好時需要用手輔助玻璃,必須使檢測器在兩片玻璃之間移動。
3, when glue is used, if the residual glue of glue head is more, it should be cleaned up in time. When cleaning, pay attention to safety and prevent auxiliary transmission of injured hand. When glass flatness is not good, hand assist glass must be used, so the detector must move between two pieces of glass.
4、每條邊的打膠情況可通過工藝里面的向上調整,上部調整,向下調整,底部調整來適當調整,每次調整需保存。
4, the glue on each side can be adjusted to the upper part in the process, the upper part should be adjusted, the bottom should be adjusted, and the bottom adjustment should be adjusted properly. Every adjustment should be saved.
5、中途需要更換玻璃厚度或綠條厚度時,待生產上次規格玻璃后一張玻璃時關閉連線,打完后一張玻璃進入輸出端停下時轉到手動狀態,進入玻璃厚度界面設置需要的玻璃厚度或綠條厚度,設置完成以后連線自動生產。
5, midway need to replace the glass thickness or green strip thickness, close the connection to the last production specifications of glass last piece of glass, finished the last piece of glass to the manual state into the output end stop when the thickness of the glass into the interface settings need glass thickness or green strip thickness, set up after the completion of the automatic production line.
6、需要排膠時先關閉連線,待打膠的玻璃打完并移動到輸出端以后按下排膠啟動按鈕,再按排膠閥。這時需要繼續生產就需要把設備旋轉到手動狀態,按下連線按鈕,再次轉到自動狀態,按下自動運行按鈕繼續生產。
6, when the glue needs to be arranged, the wire is closed first, the glass to be hit finish and then moves to the output end to press the boot button and then press the glue valve. At this point, if we need to continue production, we need to turn the equipment to the manual state, press the connection button, turn to the automatic state again, and press the automatic operation button to continue production.
本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的網站:http://linshi.jncsjx.com謝謝您的到來!
The wonderful content of this article comes from the detailed content of the double component glue machine, please click on our official website: http://linshi.jncsjx.com thank you for your arrival!
- 中空玻璃生產線有哪些設備組成 2024/06/13
- 丁基涂布機的膠嘴漏膠會(huì )不會(huì )營銷生產質量? 2024/06/13
- 雙組份打膠機的結構原理介紹 2024/06/11
- 中空玻璃設備變速裝置的作用 2024/06/09
- 玻璃涂布機設備的涂布速度會(huì )因為溫度變化而產生影響 2024/06/07
- 鋁條折彎機的設備組成介紹 2024/06/06
- 玻璃涂布機設備的使用流程 2024/05/28
- 全自動封膠線:封膠機的種類有哪些? 2024/05/24
- 玻璃涂布機設備的使用流程 2024/05/23
- 立式丁基膠涂布機的分類以及工作原理 2024/05/22
產品分類Product categories
聯系我們Contact us
- 咨詢熱線:0531-85717458 13705446998
- 公司地址: 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們: